info@strappingtoolppt.com
+91 7604 006 074
Pneumatic Steel Strap Sealer
Model No.: SPSR-32L
Pneumatic Steel Strap Sealer for 25 x 0.79 / 0.89 mm strap (Low Air Pressure) | Medium Duty Air Powered Strapping Tool | Single Notch Reverse (Up Cut) | For Regular & High Tensile Steel Straps.
Description
Improve your packaging efficiency with this medium-duty pneumatic steel strap sealer, specially designed for reliable performance with lower air pressure requirements. Featuring a single notch reverse (Up Cut) sealing mechanism, this air-powered tool ensures strong, uniform joints that enhance load stability during transportation and storage.
Download User Manual
Features:
- Medium Duty Pneumatic Steel Strap Sealer.
- Single Notch Reverse type (up cut).
- Easy to Operate & Maintain.
Specification:
- Strap Thickness : 0.64 mm – 0.89 mm / 0.025″ – 0.035″
- Strap Width : 31.75 mm / 1 ¼ “
- Grade : High Tensile, Painted and Waxed also can be used with M.S Strap.
- Joint Efficiency : 75% – 80%
- Operating Air Pressure : 4.0 Kg/cm2 – 4.5 Kg/cm2
- Weight : 4.5 kg / 9.92 lb. (approx.)
- Dimension (L × W × H ) : 290 mm × 140 mm × 265 mm / 11.42″ × 5.51″ × 10.43″
| Index No. | Part Number | Part Name | Quantity |
|---|---|---|---|
| 1 | SP32E0001F | SIDE PLATE | 2 |
| 2 | SP32E0002F | NOTCHER PLATE (TYPE-A) | 2 |
| 3 | SP32E0003F | SPACER FOR NOTCHER | 1 |
| 4 | SP32E0004F | LINKS | 4 |
| 5 | SP3219C05F | JAW | 2 |
| 6 | SP3219C06F | JAW LINK PIN | 2 |
| 7 | SP3219C07F | BOLT FOR JAW NOTCHER SIDE PLATE | 2 |
| 8 | SP3219C08F | PISTON ROD | 1 |
| 9 | SP3219C09F | SLIDER PIN | 1 |
| 10 | SP3219C10F | BOLTS FOR SIDE PLATE & CYLINDER HEAD | 2 |
| 11 | SP3219C11B | HEX NUT M8 | 3 |
| 12 | SP3219C12B | NUT FOR PISTON ROD | 1 |
| 13 | SP3219C13B | OIL SEAL FOR PISTON | 1 |
| 14 | SP3219C14B | PISTON | 1 |
| 15 | SP3219C15B | CONICAL SPRING FOR PISTON | 1 |
| 16 | SP3219C16F | CYLINDER HEAD | 1 |
| 17 | SP3219C17F | CYLINDER BODY | 1 |
| 18 | SP32E0018B | SCREW FOR CYLINDER HEAD | 4 |
| 19 | SP3219C19F | AIR INLET NUT | 1 |
| 20 | SP3219C20B | C-PIN-1 | 1 |
| 21 | SP3219C21B | SERRATED WASHER | 4 |
| 22 | SP3219C22F | TRIGGER | 1 |
| 23 | SP3219C23F | TRIGGER LINK | 1 |
| 24 | SP3219C24F | VALVE BODY | 1 |
| 25 | SP3219C25F | VALVE BODY WASHER | 2 |
| 26 | SP3219C26F | WASHER LOCK (LONG) | 1 |
| 27 | SP3219C27B | VALVE POPPET WASHER | 2 |
| 28 | SP3219C28F | VALVE POPPET | 1 |
| 29 | SP3219C29B | C-PIN-2 | 1 |
| 30 | SP3219C30B | C-PIN-3 | 1 |
| 31 | SP3219C31F | WASHER LOCK (SHORT) | 1 |
| 32 | SP3219C32B | SPRING FOR VALVE | 1 |
| 33 | SP3219C33F | SPRING CAP | 1 |
| 34 | SP3219C34B | O-RING FOR VALVE BODY | 1 |
| 35 | SP3219C35F | BOLT FOR SIDE PLATE NOTCHER & SPACER | 1 |
| 37 | SP3219C37B | NYLOCK NUT M8 | 2 |
OPERATIONAL MANUAL:
- Before connecting the pneumatic hose connector with machine please check the FRL is fitted with pneumatic hose line and the hose is in safe working condition.
- Connect the pneumatic connector with the tool.
- Check the on line air pressure.
- Hold the tool vertically and place the jaws across the seal. This seal is very important as improper crimping (off-center) may cause the strap to become loose and snap apart, possibly resulting in serious injury.
- Press the trigger to seal the strap.
- Remove the sealer & inspect the seal to verify the seal is properly holding the strap. The seal should have two impressions, one on each side. The notches should be cantered on the seal. If impression isn`t properly formed, remove it & do it again with new seal & strap. Attempting to reseal will not ensure a proper seal & will decrease the break strength.
- If double notch is required then repeat the 4th operation after placing. The tool over the seal maintain proper space from the previous notch.
MAINTENANCE:
DAILY INSPECTION:
- Perform a daily visual inspection for any signs of wear or damage.
- Check and tighten all bolts and fasteners.
- Lubricate all moving parts before operating the machine – especially the lubricating point provided in the machine.
WEEKLY INSPECTION:
- Clean the machine to prevent dust and debris build-up.
- Check and tighten all bolts and fasteners.
- Replace any worn-out components.
MONTHLY INSPECTION:
- Inspect critical components for signs of wear and replace if necessary.
- Maintain a log of all maintenance activities.
QUARTERLY INSPECTION:
- Conduct a thorough inspection of the entire system.
- Replace any worn-out components.
ANNUAL INSPECTION:
- Perform a comprehensive overhaul of the system.
- Schedule a professional inspection and servicing.
SAFETY INSTRUCTIONS:
- Only trained personnel should operate above mentioned tools.
- Wear Gloves, Safety shoe, Helmet & Goggle before starting operation.
- Remove oil or grease from your hands, tools and from working area.
- Keep fingers away from areas that can pinch or cut. These areas are primarily located at the front of the tool.
- Only use this tool recommended for the strap which is specified in the catalogue.
Related Products
