MODEL : SSR-114H
- Heavy duty steel strap Sealer.
- Single Notch reverse type (up cut) side action.
- Strap thickness – 1.10 mm-1.27mm /0.044” – 0.050”
- Strap width – 31.75mm / 1 1/ 4 “
- Grade – High Tensile
- Heavy duty Manual Steel Strap Sealer.
- Single Notch reverse type (up cut) side action.
- Easy to operate & maintain.
Strap Thickness : 1.10 mm – 1.27 mm / 0.044” – 0.050”
Strap width: 31.75mm / 1 1/ 4 “
Grade: High Tensile.
Joint Efficiency: 75% to 80%
Weight:3.5 kg / 7.71 lb(approx)
Dimension (L X W X H): 758mm X 35mm X 100 mm / 29.8″ X 1.37″ X 3.93″
|
INDEX NO. |
PART NUMBER |
PART NAME |
QTY |
|
1 |
MSSU1114HA |
UPPER HANDLE HEAD WITH PIPE |
1 |
|
2 |
MSSU2114HA |
LOWER HANDLE HEAD WITH PIPE |
1 |
|
3 |
MSSU03114F |
SIDE PLTE-R |
1 |
|
3A |
MSSU3A114F |
SIDE PLTE-L |
1 |
|
4 |
MSSU41140F |
ROUND LINK BAR |
1 |
|
5 |
MSSU51140F |
STRAIGHT LINK BAR |
1 |
|
6 |
MSSU61140F |
JAW |
2 |
|
7 |
MSSU71140F |
CENTER LINK |
2 |
|
8 |
MSSU81140F |
CENTER LINK PIN |
1 |
|
9 |
MSSU91140F |
SPACER |
1 |
|
10 |
MSSU10114F |
JAW LINK PIN FOR BOTH LINK BAR |
2 |
|
11 |
MSSU11114F |
UPPER HANDLE LINK PIN FOR CENTER LINK |
1 |
|
12 |
MSSU12114B |
STOPPER BOLT WITH NUT |
1 |
|
13 |
MSSU13114B |
BOLT FOR LOWER HANDLE & SPACER |
3 |
|
13A |
MSSU13A14F |
BOLT FOR UPPER HANDLE & JAW |
3 |
|
14 |
MSSU14114B |
NYLOCK NUT FOR BOLT |
3 |
|
14A |
MSSU14A14B |
NYLOCK NUT FOR BOLT |
3 |
|
15 |
MSSU15114F |
HANDLE GRIPPER |
2 |
|
NOTE: BELOW ITEMS SHOULD BE PURCHASE AS ASSEMBLY PART |
|||
|
1 & 12 |
MSSU1214SA |
UPPER HANDLE ASSEMBLY |
1SET |
OPERATIONAL MANUAL
1. Hold the `SSR-114H` vertically, opened the Jaws & place the jaws across the seal. This seal is very important as the seal crimped the off-center may cause the strap become loose & snap apart, possibly resulting in serious injury.
2. Press the handle of the sealer together until the proper sealing done, while keeping the sealer in vertical position.
3. Remove the sealer & inspect the seal to verify the seal is properly holding the strap. The seal should have four impressions, one on each side. The notches should be centered on the seal. If impression isn`t properly formed, remove it & do it again with new seal & strap. Attempting to reseal will not ensure a proper seal & will decrease the break strength.
4. Never use the sealer to break the strap. Breaking the strap without the proper cutter may cause the strap to snap back towards the operator, possibly resulting in serious injury. This action will also cause damage to the sealer, which will require the sealer to be repaired or replaced at owner`s expense.
SAFETY INSTRUCTIONS
1. Only trained personnel should operate `SSR-114H`.
2. Wear Gloves, Safety shoe, Helmet & Google before starting operation.
3. Keep fingers away from areas that can pinch or cut. These areas are primarily located at the front of the tool.
4. Only use equipment recommended for the strap.`SSR-114H` is recommended only for 1.10 mm to 1.27 mm
thick X 31.75 mm width.