MODEL : SSN-114H
- Heavy duty steel strap Sealer.
- Single Notch regular type (Down cut) side action.
- Strap thickness – 1.10 mm-1.27mm /0.044” – 0.050”
- Strap width – 31.75mm / 1 1/ 4 “
- Grade – High Tensile
- Medium duty Manual Steel Strap Sealer
- Single Notch regular type (Down cut) side action
- Easy to operate & maintain
Strap Thickness : 1.10 mm – 1.27 mm / 0.044” – 0.050”
Strap width: 31.75mm / 1 1/ 4 “
Grade: Regular Duty or High Tensile.
Joint Efficiency: 75% to 80%
Weight: 4.2kg / 9.259 lb(approx)
Dimension (L X W X H): 760 x 50 x 280 mm / 29.9” x 2” x 11”
|
INDEX |
PART NUMBER |
PART NAME |
QUANTITY |
|
01 |
MSSD01230F |
JAW |
4 |
|
02 |
MSSD02230F |
NOTCHER PLATE |
1 |
|
03 |
MSSD03230F |
PIN FOR JAW & NOTCHER |
2 |
|
04 |
MSSD04230F |
LINK BAR |
1 |
|
05 |
MSSD05230F |
LINK BAR PIN |
4 |
|
06 |
MSSD06230F |
LINK |
1 |
|
07 |
MSSD07230B |
HANDLE GRIP |
2 |
|
08 |
MSSD08230F |
SIDE PLATE |
2 |
|
09 |
MSSD09230B |
M8 BOLT |
4 |
|
10 |
MSSD10230F |
LOWER HANDLE HEAD ASSEMBLY |
1 |
|
11 |
OMITTED |
OMITTED |
OMITTED |
|
12 |
MSSD12230F |
UPPER HANDLE HEAD ASSEMBLY |
1 |
|
13 |
MSSD13230B |
NYLOCK NUT M8 SIZE |
4 |
|
14 |
MSSD14230F |
PIN FOR SIDE PLATE, UPPER HANDLE HEAD, JAW & NOTCHER |
3 |
|
15 |
MSSD15230F |
UPPER HANDLE HEAD REST PIN |
1 |
OPERATIONAL MANUAL
1. Hold the `SSN-114H` vertically, opened the Jaws & place the jaws across of the seal. This step is very
important as a seal crimped of the off-center may cause the strap to become loose & snap apart, possibly
resulting in serious injury or death.
2. Press the handle of the sealer together until the proper sealing done, while keeping the sealer in vertical
position.
3. Remove the sealer & inspect the seal to verify the seal is properly holding the strap. The seal should have two
impressions, one on each side. The notches should be centered on the seal. If seal isn`t properly formed,
remove it & do it again with new seal & strap. Attempting to reseal will not ensure a proper seal & will
decrease the break strength.
4. Never use the sealer to break the strap. Breaking the strap without the proper cutter may cause the strap to
snap back towards the operator, possibly resulting in serious injury or death. This action will also cause
damage to the sealer, which will require the sealer to be repaired or replaced at owner`s expense.
SAFETY INSTRUCTIONS
1. Only trained personnel should operate `SSN-114H`.
2. Wear Gloves, Safety shoe, Helmet & Google before starting operation.
3. Keep fingers away from areas that can pinch or cut. These areas are primarily located at the front of the tool.
4. Only use equipment recommended for the strap.`SSN-114H` is recommended only for 1.10 mm to 1.27 mm
thick X 31.75 mm width.