MODEL : HSNDS-11457
- Strap Thickness : 1.45 mm/0.057 ̎
- Strap width : 31.75mm / 1 1/ 4 “
- Grade : High Tensile.
- Joint Efficiency : 75 % to 80 %.
- Weight : 4.2 kg / 9.259 lb(approx)
- Heavy Duty Manual Steel Strap Sealer.
- Suitable for working with steel strapping.
Handy Tool. - Single Notch regular type (Down cut) side action.
- Easy to operate & maintain.
Strap Thickness : 1.45 mm/0.057 ̎
Strap width : 31.75mm / 1 1/ 4 “
Grade : High Tensile.
Joint Efficiency : 75 % to 80 %.
Weight : 4.2 kg / 9.259 lb(approx)
Dimension (L X W X H) : 745×48×278mm / 29.3̎ × 1.9̎ ×10.9 ̎
|
INDEX |
PART NUMBER |
PART NAME |
QUANTITY |
|
01 |
MSSD01230F |
JAW |
4 |
|
02 |
MSSD02230F |
NOTCHER PLATE |
1 |
|
03 |
MSSD03230F |
PIN FOR JAW & NOTCHER |
2 |
|
04 |
MSSD04230F |
LINK BAR |
1 |
|
05 |
MSSD05230F |
LINK BAR PIN |
4 |
|
06 |
MSSD06230F |
LINK |
1 |
|
07 |
MSSD07230B |
HANDLE GRIP |
2 |
|
08 |
MSSD08230F |
SIDE PLATE |
2 |
|
09 |
MSSD09230B |
M8 BOLT |
4 |
|
10 |
MSSD10230F |
LOWER HANDLE HEAD |
1 |
|
11 |
OMITTED |
OMITTED |
OMITTED |
|
12 |
MSSD12230F |
UPPER HANDLE HEAD |
1 |
|
13 |
MSSD13230B |
NYLOCK NUT M8 SIZE |
4 |
|
14 |
MSSD14230F |
PIN FOR SIDE PLATE, UPPER HANDLE HEAD, JAW & NOTCHER |
3 |
|
15 |
MSSD15230F |
UPPER HANDLE HEAD REST PIN |
1 |
OPERATIONAL MANUAL
1. Hold the `HSNDS-11457` vertically, opened the Jaws & place the jaws across the seal. This seal is very important as the seal crimped the off-center may cause the strap become loose & snap apart, possibly resulting in serious injury.
2. Press the handle of the sealer together until the proper sealing done, while keeping the sealer in vertical position.
3. Remove the sealer & inspect the seal to verify the seal is properly holding the strap. The seal should have four impressions, one on each side. The notches should be centered on the seal. If impression isn`t properly formed, remove it & do it again with new seal & strap. Attempting to reseal will not ensure a proper seal & will decrease the break strength.
4. Never use the sealer to break the strap. Breaking the strap without the proper cutter may cause the strap to snap back towards the operator, possibly resulting in serious injury. This action will also cause damage to the sealer, which will require the sealer to be repaired or replaced at owner`s expense.
SAFETY INSTRUCTIONS
- 1. Only trained personnel should operate `HSNDS-11457`.
- 2. Wear Gloves, Safety shoe, Helmet & Goggle before starting operation.
- 3. Keep fingers away from areas that can pinch or cut. These areas are primarily located at the front of the tool.
- 4. Only use equipment recommended for the strap.`HSNDS-11457` is recommended only for 1.45mm thick × 31.75mm width.