MODEL : SPSR-25
- Strap Thickness: 0.64mm – 0.89mm // 0.025 ̎- 0.035 ̎
- Strap width: 25.4mm/ 1 ̎
- Grade: Regular Duty or High Tensile.
- Joint Efficiency: 75% to 80%
- Operating Air Pressure: 6.0-6.5 kg/cm2
- Medium duty Pneumatic Steel Strap Sealer
- Single Notch reverse type (up cut)
- Easy to operate & maintain
|
Strap Thickness |
: |
0.64mm – 0.89mm // 0.025 ̎- 0.035 ̎ |
|
Strap width |
: |
25.4mm/ 1 ̎ |
|
Grade |
: |
Regular Duty or High Tensile. |
|
Joint Efficiency |
: |
75% to 80% |
|
Operating Air Pressure |
: |
6.0-6.5 kg/cm2 |
|
Weight |
: |
3.4kg / 7.49 lbs. (Approx) |
|
Dimension (L X W X H) |
: |
258mm ×110mm ×252mm / 10.15̎×4.33 ̎× 9.92 ̎ |
|
INDEX NO. |
PART NUMBER |
PART NAME |
QUANTITY |
|
1 |
SP25E0001F |
SIDE PLATE |
2 |
|
2 |
SP25E0002F |
NOTCHER PLATE (TYPE-A) |
2 |
|
3 |
SP25E0003F |
SPACER FOR NOTCHER |
1 |
|
4 |
SP25E0004F |
LINKS |
4 |
|
5 |
SP25E0005F |
JAW |
2 |
|
6 |
SP3219C06F |
JAW LINK PIN |
2 |
|
7 |
SP25E0007F |
PIN FOR JAW, NOTCHER AND SIDE PLATE |
2 |
|
8 |
SP3219C08F |
PISTON ROD |
1 |
|
9 |
SP3219C09F |
SLIDER PIN |
1 |
|
10 |
SP3219C10F |
BOLTS FOR SIDE PLATE & CYLINDER HEAD |
2 |
|
11 |
SP3219C11B |
HEX NUT M8 |
1 |
|
12 |
SP3219C12B |
NUT FOR PISTON ROD |
1 |
|
13 |
SP3219C13B |
OIL SEAL FOR PISTON |
1 |
|
14 |
SP3219C14B |
PISTON |
1 |
|
15 |
SP3219C15B |
CONICAL SPRING FOR PISTON |
1 |
|
16 |
SP3219C16F |
CYLINDER HEAD |
1 |
|
17 |
SP3219C17F |
CYLINDER BODY |
1 |
|
18 |
SP3219C18B |
SCREW FOR CYLINDER HEAD |
4 |
|
19 |
SP32E0019B |
AIR INLET NUT |
1 |
|
20 |
SP3219C20F |
C-PIN-1 |
1 |
|
21 |
SP3219C21B |
SERRATED WASHER |
4 |
|
22 |
SP3219C22B |
TRIGGER |
1 |
|
23 |
SP3219C23F |
TRIGGER LINK |
1 |
|
24 |
SP3219C24F |
VALVE BODY |
1 |
|
25 |
SP3219C25F |
VALVE BODY WASHER |
2 |
|
26 |
SP3219C26F |
WASHER LOCK(LONG) |
1 |
|
27 |
SP3219C27B |
VALVE POPPET WASHER |
2 |
|
28 |
SP3219C28F |
VALVE POPPET |
1 |
|
29 |
SP3219C29F |
C-PIN-2 |
1 |
|
30 |
SP3219C30F |
C-PIN-3 |
1 |
|
31 |
SP3219C31B |
WASHER LOCK(SHORT) |
1 |
|
32 |
SP3219C32B |
SPRING FOR VALVE |
1 |
|
33 |
SP3219C33F |
SPRING CAP |
1 |
|
34 |
SP3219C34F |
O-RING FOR VALVE BODY |
1 |
|
35 |
SP3219C35B |
BOLT FOR SIDE PLATE NOTCHER & SPACER |
1 |
|
36 |
SP3219C36B |
RUBBER JACKET |
1 |
|
37 |
SP3219C37B |
NYLOCK NUT M8 |
2 |
OPERATIONAL MANUAL
1. Before connecting the pneumatic hose connector with machine please check the FRL is fitted with pneumatic hose line and the hose in safe
working condition.
2. Connect the pneumatic connector with the tool.
3. Check the on line air pressure.
4. Hold the tool vertically & place the jaws across the seal. This seal is very important as the seal crimped the off-center may cause the strap become
loose & snap apart, possibly resulting in serious injury.
5. Press the trigger to seal the strap.
6. Remove the sealer & inspect the seal to verify the seal is properly holding the strap. The seal should have two impressions, one on each side. The
notches should be centered on the seal. If impression isn`t properly formed, remove it & do it again with new seal & strap. Attempting to reseal will
not ensure a proper seal & will decrease the break strength.
SAFETY INSTRUCTIONS
1. Only trained personnel should operate above mentioned tools.
2. Wear Gloves, Safety shoe, Helmet & Goggle before starting operation.
3. Remove oil or grease from your hands, tools and from working area.
4. Keep fingers away from areas that can pinch or cut. These areas are primarily located at the front of the tool.
5. Only use this tool recommended for the strap which is specified in the catalogue.