MODEL : HPTR-11450

Strap Thickness: 1.27mm / 0.050 ̎

Strap width: 31.75 mm / 1¼ ̎

Grade: High Tensile, Heavy Duty, Painted & Waxed.

Operating Air Pressure: 6.5 to 7 bar.

Air consumption: 14.0 to 15.0 CFM (During Tensioning)

Weight: 6.5 kg/14.3lb (Approx)

Dimension (LXWXH): 385x140x150mm/15.15”x5.51”x 5.90”

Tension Achievable: 4000 lb/1740 N

SPARE PART LIST FOR AIR MOTOR ASSY. Of HPTR-11450

PART NO.	PART NUMBER	PART NAME	QTY.
01	HPTRC0001F	ADOPTER	01
02	HPTRC0002B	AIR FILTER (Ø42X.5)	01
03	HPTRC0003B	CONICAL VALVE SPRING	01
04	HPTRC0004F	VALVE	01
05	HPTRC0005B	VALVE PIN (Ø4X29)	01
06	HPTRC0006F	CONTROL RING	01
07	HPTRC0007F	VALVE BODY	01
08	HPTRC0008B	LOCATING PIN (Ø3X25)	01
09	HPTRC0009B	BEARING NO. 1 FOR END PLATE 1	01
10	HPTRC0010F	END PLATE NO. 1	01
11	HPTRC0011B	LOCATING PIN (Ø2.5X9.8)	07
12	HPTRC0012F	ROTOR	01
13	HPTRC0013B	ROTOR VANE	05
14	HPTRC0014F	AIR CYLINDER	01
15	HPTRC0015F	END PLATE NO. 2	01
16	HPTRC0016B	BEARING NO. 2 FOR END PLATE-2	01
17	HPTR50017F	AIR MOTOR BODY	01
18	HPTRC0018F	SILENCER	01
19	HPTRC0019B	WIRE LOCK	01
20	HPTR50020F	GEAR HOUSING FOR LOCKING SCREW	01
21	HPTRC0021F	1 MODULE IDLE GEAR (GEAR BOX 1&2)	06
22	HPTRC0022F	1 MODULE INTERNAL GEAR (GEAR BOX 1)	01
23	HPTRC0023B	PIN FOR PLANET HOLDER-1 & PLANET HOLDER -2	06
24	HPTRC0024F	1 MODULE PLANET HOLDER-1	02
25	HPTRC0025B	BEARING NO. 3 FOR BEARING HOUSING NO.-1	02
26	HPTRC0026F	BEARING HOUSING NO.-1	01
27	HPTRC0027F	FLAT WASHER	01
28	HPTRC0028F	1 MODULE INTERNAL GEAR(GEAR BOX 2)	01
29	HPTRC0029F	BEARING HOUSING NO.-2	01
30	HPTR50030F	TIGHTNING NUT	01
31	HPTR50031F	BEARING HOUSING BODY	01

SPARE PART LIST FOR WORM HOUSING AND ROLLER FRAME ASSY. Of HPTR-11450

PART NO.	PART NUMBER	PART NAME	QTY.
32	HPTR50032F	FRONT COVER FOR WORM HOUSING	01
33	HPTR50033F	1MODULE INTERNAL GEAR	01
34	HPTR50034F	1MODULE IDLE GEAR	03
35	HPTR50035F	1MODULE PLANET HOLDER FOR WORM	01
36	HPTR50036F	SPACER	01
37	HPTR50037B	BEARING NO.4	01
38	HPTR50038F	WORM SHAFT	01
39	HPTR50039F	WORM SHAFT KEY	01
40	HPTR50040F	WORM HOUSING	01
41	HPTR50041F	NEEDLE BEARING NO.5	01
42	HPTR50042F	NEEDLE BEARING COVER DISH	02
43	HPTRC0043F	SMALL CIRCLIP	01
44	HPTR50044B	CSK SCREW FOR WORM HOUSING ADJUSTING BOLT REST	01
45	HPTR50045B	BEARING NO.6	02
46	HPTR50046F	WORM WHEEL	01
47	HPTR50047F	FEED WHEEL SHAFT	01
48	HPTR50048F	BEARING COVER	01
49	HPTR50049B	BIG CIRCLIP	01
50	HPTR50050F	HANDLE	01
51	HPTR50051B	ALLEN BOLT	05
52	HPTR50052F	ROLLER FRAME	01
53	HPTRC0053F	PRESSURE PAD	01
54	HPTRC0054B	C PIN FOR PRESSURE PAD	01
55	HPTR50055F	FEEDWHEEL	01
56	HPTR50056F	OILET BUSH	01
57	HPTR50057F	LINK	01
58	HPTR50058B	C PIN FOR LINK	01
59	HPTR50059F	SPINDLE FOR ROLLER FRAME & LINK	01
60	HPTR50060F	HOUSING BASE COVER	01
61	HPTRC0061B	CSK SCREW FOR HOUSING BASE COVER	04
62	HPTRC0062F	TENSIONING SPRING	01
63	HPTR50063F	TENSIONING SPRING COVER	01
64	HPTR50064B	GRUB SCREW FOR WORM HOUSING	02
65	HPTR50065F	ROUND NUT FOR SPNDLE	01

Pull the strap from the coil & insert the strap in to the seal in such a way so that flat surface of the seal remains facing outside the strap.
Apply the strap around the package and bottom strap insert through the seal. Then hold the overlap portion of the straps with your left hand.
Bend the extended strap as Hook against the seal.
Pull out excess slack with your right hand.
Hold together the handle and body of the air motor with your right hand and lift upward the air motor portion against the handle to make gap between feed wheel & lower Roller.
Insert the top strap under the strap guide & feed wheel of the tool, at the same time push the tool forward against the Seal, and release by the air motor body.
Turn the Control ring clockwise for tensioning until the proper tension achieved & switch off the motor by turning the control ring anti -clockwise.
Seal the strap by using the recommended Sealer.
Swing the tool up & down until the strap is cut off.
Lubricate the machine at the start of the Shift and at the end of the Shift.

NOTE: Install FRL Unit in every line where pneumatic machines are running.

Before using the tool, read the operating instructions carefully.
Wear hand gloves, safety shoe, Helmet, goggles during operation.
When cutting the strap hold the upper portion and stand safely away from the strap.
Do not stand in line with the strap while it is tensioned. The strap may break.
Do not put your fingers into the Tensioner wheel area.
Do not put your hand under the strap on the job while strap is tensioned.
Only use equipment recommended for the strap. `HPTR-11450’ are recommended only for up to 1.27mm mm thick. X 31.75mm width.

Suggest Item